Development engineering on Siemens

Guaranteed migration
of your Siemens HMI.

From Comfort, Basic or Runtime Advanced to WinCC Unified or to an open web platform: you choose the destination. Fast, simple and turnkey: tell us what you have and we hand it back running.

First meeting free of charge · Reply within 24 working hours

In 46 seconds

This is what a migration looks like.

From the panel you have today to WinCC Unified or the web, with the same machine underneath.

You choose

Two destinations. The same guarantee.

Siemens

WinCC Unified

The natural successor of your Siemens HMI, inside TIA Portal: Unified Comfort and Unified Basic panels, or Unified PC Runtime.

  • A direct successor for every panel
  • Same cut-out at 7″ and 12″
  • Your familiar TIA Portal ecosystem
Open

Open web platform

An HTML5 HMI that opens in any browser, panel or tablet, connected to your Siemens PLC over OPC UA, S7 or MQTT.

  • No runtime licence per station
  • On any screen or browser
  • Not tied to any HMI vendor
That simple

Three steps and your machine has a new screen.

  1. 1

    Tell us what you have

    A one-minute assessment and a first meeting free of charge.

  2. 2

    We migrate it

    We rebuild your HMI in WinCC Unified or on the open web and test it in simulation before touching the machine.

  3. 3

    It starts up on site

    We swap the panel, test it with your team and hand everything over documented.

Our guarantee

If it does not work like before, it is not finished.

We do not close the migration until your machine runs on site with the new HMI just as it did with the old one, and your team has tested it with us.

  • Tested in simulation before going on site
  • Validated with your team, on your machine
  • Delivered with the HMI security documentation
Before and after

Same machine. A different screen.

Drag and compare. Your machine does the same; the screen is modern, secure and visible wherever you need it.

L1_FILLER12:04
TANK A  77 %
! 0042 Low level in tank B
F1HomeF2AlarmsF3RecipesF4TrendF5UserF6System
Filler L1Running
Operator
Tank A level77 %
Speed119 bpm
Temperature21.9 °C
Counter4,530
  • Low level in tank B
  • Guard door open
  • Format change completed
TLSRolesAccess log

Demo screen of a filling machine. Not a customer project.

What you gain

More than a new screen.

  • Modern screens

    Multi-touch, clearer and easier for operators.

  • From the browser

    Your HMI on the office PC or on a tablet too.

  • More secure

    Users, roles and protected communications by design.

  • Built to last

    A current platform, with support ahead of it.

  • Minimal downtime

    We prepare everything first; on site we only swap the panel.

  • One partner

    From the first analysis to handover, one team.

385daysto 11-12-2027
The time is now

Siemens is phasing out Comfort and the CRA arrives in 2027.

From 11 December 2027 the Cyber Resilience Act (CRA) fully applies: new machinery sold in the EU will have to comply with it, HMI included. Migrating in good time costs less than migrating in a hurry. Regulation (EU) 2024/2847

Model by model

What happens to each device.

Choose your HMI family: what it moves to, what changes in the cabinet and what is rebuilt. Based on the Siemens guides.

How do you migrate a Comfort Panel to WinCC Unified?

There is no automatic migration. Siemens states in its changeover guide that, because of the functional differences between the two generations, a Comfort Panel configuration cannot be migrated directly: the project is rebuilt in WinCC Unified. The free Data2Unified add-in transfers part of the data, such as texts in several languages, and VBScript scripts are rewritten in JavaScript.

The hardware does have a successor for almost every model: TP700, TP900 and TP1200 Comfort move to MTP700, MTP1000 and MTP1200 Unified Comfort; KTP400, KTP700, KTP900 and KTP1200 Basic to MTP400, MTP700, MTP1000 and MTP1200 Unified Basic. WinCC Runtime Advanced moves to WinCC Unified PC Runtime, with a new licence.

Which Unified device replaces each one

WinCC Unified successors of Comfort and Basic Panels and WinCC Runtime Advanced
Current deviceWinCC Unified successorCut-out and mounting
TP700 ComfortMTP700 Unified ComfortSame cut-out (197 × 141 mm)
TP900 ComfortMTP1000 Unified ComfortEnlarge the cut-out from 250 × 166 mm to 264 × 189 mm
TP1200 ComfortMTP1200 Unified ComfortSame cut-out (310 × 221 mm)
TP1500, TP1900 and TP2200 ComfortMTP1500, MTP1900 and MTP2200 Unified ComfortSmaller cut-out: the existing one is reused with an adapter frame
Comfort key panels (KPxx00 Comfort)Unified Comfort with SIMATIC Key Panel KP8 PN LXHardware keys move to a separate panel, over PROFINET IO
KTP400 ComfortMTP400 Unified Basic, if its functions are enoughSame dimensions; otherwise a larger Unified Comfort with an enlarged cut-out
KTP400 BasicMTP400 Unified BasicSame dimensions; resolution from 480 × 272 to 800 × 480
KTP700 BasicMTP700 Unified BasicSame cut-out
KTP900 BasicMTP1000 Unified BasicEnlarge the cut-out to 264 × 189 mm; resolution from 800 × 480 to 1280 × 800
KTP1200 BasicMTP1200 Unified BasicSame cut-out
WinCC Runtime Advanced (PC)WinCC Unified PC RuntimeNo licence upgrade: new licence by PowerTags

2nd generation Basic key panels also move to Unified with the KP8 PN LX. Unified Basic Panels have no PROFIBUS port.

Source: Siemens changeover guides to WinCC Unified, entry 109768002 (Comfort V4.0 06/2023, Basic V1.0 09/2024, Runtime Advanced V2.0 05/2022).

Assessment · 1 minute

What needs migrating?

Four questions and we tell you what each device moves to and how urgent it is.

  1. →Your plan
What best describes you?
FAQ

Frequently asked questions

What does «guaranteed migration» mean?

That we do not close the migration until your machine runs on site with the new HMI just as it did with the old one and your team has tested it with us. The guarantee covers the migration work; compliance with regulations such as the CRA belongs to the machine manufacturer.

Can a Comfort Panel be migrated automatically to WinCC Unified?

No. Siemens states in its changeover guide (entry 109768002) that a Comfort Panel configuration cannot be migrated directly. The project is rebuilt in WinCC Unified; the Data2Unified add-in transfers part of the data and VBScript scripts are rewritten in JavaScript.

Which Unified panel replaces the TP700 Comfort?

The MTP700 Unified Comfort. It has the same cut-out as the TP700 Comfort, 197 × 141 mm, so the cabinet does not change. The TP1200 Comfort moves to the MTP1200 in the same way.

Does the cabinet cut-out have to change?

Not for 7″ and 12″. The TP900 Comfort and KTP900 Basic move to a 10″ panel and the cut-out is enlarged to 264 × 189 mm. At 15″, 19″ and 22″ the Unified panel is smaller and is mounted in the existing cut-out with an adapter frame.

How long will the machine be stopped?

As little as possible. We prepare and test the new HMI in simulation before going on site, so at the machine we only swap the panel and validate it with your team. Shutdowns are planned with you.

What replaces the TP900 Comfort?

The MTP1000 Unified Comfort. There is no 9″ Unified Comfort, so the cut-out is enlarged from 250 × 166 mm to 264 × 189 mm.

What replaces the Basic Panels?

The Unified Basic Panels: KTP400, KTP700, KTP900 and KTP1200 Basic move to MTP400, MTP700, MTP1000 and MTP1200 Unified Basic. They have no PROFIBUS port.

Do Unified Basic Panels have PROFIBUS?

No. If your Basic Panel talks PROFIBUS, we review the PLC connection before choosing the device.

Can a WinCC Runtime Advanced licence be upgraded to Unified?

No. Siemens states that a Runtime Advanced licence cannot be upgraded to WinCC Unified PC Runtime. A new licence is needed, priced by PowerTags (tags connected to the PLC), plus one per web client.

Can the HMI be viewed from a tablet?

Yes. WinCC Unified PC Runtime serves the HMI over the web to panel PCs, tablets or phones, with one web client licence each. The open web platform runs in any browser.

Does the CRA force me to replace panels already installed?

No. Regulation (EU) 2024/2847 fully applies from 11-12-2027 to products placed on the market from that date and does not require removing installed equipment. It does affect new machinery shipped from then on with its HMI.

WinCC Unified or an open web platform?

You choose. WinCC Unified is the most direct path from a TIA Portal project and keeps your HMI in the Siemens ecosystem. The open web platform is an HTML5 HMI connected to your PLC over OPC UA, S7 or MQTT, viewable in any browser, with no runtime licence per station. The assessment tells you which fits best; the guarantee is the same.

How much does it cost?

It depends on the number of screens, the scripts and how many panels there are. The first analysis meeting is free of charge and ends with a proposal with scope, schedule and budget.

Your Siemens HMI, migrated. Guaranteed.

Tell us what you have and we will send you the migration plan.

SIMATIC, WinCC and TIA Portal are trademarks of Siemens AG. ISIGECO is not affiliated with Siemens. Technical data come from the guides published by Siemens.